How to repair a sliding wardrobe and save on a master

How is the wardrobe

Sliding wardrobes are of two types: cabinet – when the furniture has side walls, top and bottom, as well as built-in – when all this is replaced by a niche in the wall. Otherwise, there are no cardinal differences: inside the cabinet there are shelves, drawers and clothes rails. The front is covered with sliding doors.

Sliding system device. Illustration: Artyom Kozoriz / Lifehacker

At the corners of each leaf there are rollers that move inside the grooves of the guide profiles attached to the top and bottom of the cabinet. In the closed position, the doors are fixed with special stoppers that keep the rollers from moving. And the buffer tape along the edges of the leaves protects the profiles from impacts and softens the closing of the doors.

Of all the elements of the cabinet, the sliding system is the most complex, and it is with it that most breakdowns are associated.

Reading now 🔥

How to repair a closet if the doors do not close tightly

Very often, over time, and with poor-quality installation – immediately, the cabinet doors do not close completely. There is a gap between them and the side wall at the top or bottom. This happens due to incorrect adjustment. The problem is fixed like this.

Illustration: Artyom Kozoriz / Lifehacker

Carefully peel off the buffer tape at the bottom of the door profile where the leaf rests against the side wall. You will see two holes. Take a 4mm or 5mm hex wrench and insert it into the bottom slot. Move a little so that the hexagon fits into the head of the screw.

Now, by turning the key, adjust the position of the door . Turning it clockwise raises the sash and reduces the clearance from below. If you turn it counterclockwise, the door will lower, thereby reducing the gap at the top. It is necessary to achieve such a position that the gaps at the bottom and top are the same.

What to do if the damper tape has peeled off

A trifling problem, but nevertheless very annoying. The fleecy strip has an adhesive base, with which it is attached to the profile. Over time, the edge dries up and the tape moves away, dangling back and forth as the door moves.

Illustration: Artyom Kozoriz / Lifehacker

There are several solutions here. The easiest way is to glue the torn end of the tape with rubber or cyanoacrylate glue. You can also completely remove the old strip, clean the profile with a degreaser from adhesive residue, and then attach a new tape. They are inexpensive and are sold in furniture fittings stores.

Another option is to use special clamping brackets. They will fix the edge of the tape and will not let it move, even if it has already partially peeled off.

How to repair a closet if the doors roll back

Stoppers are used to fix the closed sashes. These are special spring-loaded brackets in the grooves of the lower guides that stop the roller in the desired position and prevent it from rolling back. With an unadjusted or broken stopper, the sash is blocked before it reaches the side wall or is fixed at all. As a result, the door closes tightly.

Illustration: Artyom Kozoriz / Lifehacker

For correct adjustment, close the sash, raise it slightly and mark the position of the roller with a pencil. Move the door to the side so as not to interfere. Now move the stopper, aligning it exactly to the center of the mark. To do this, press on one of the antennae with a screwdriver, and then push the stopper in the desired direction with your hand or a second screwdriver.

To keep the retainer in place longer, remove it and unbend the antennae wider – so they will dig deeper into the profile and hold on tighter. To do this, lift the sashes one by one and carefully remove them. Then unscrew the screws from the lower guide profile and remove it. Now the stopper can be pulled out by sliding to the edge.

If one of the retainer’s antennae is broken, it will no longer hold in the guide. In this case, you need to buy a new stopper and replace it by removing the doors and taking out the profile as described above.

To prevent the stopper from moving, you can also fix it around the edges. To do this, drill a hole with a thin drill and insert a carnation there, or simply wrap it with a small self-tapping screw.

Experienced furniture makers do not use stoppers at all, but simply make a dent on the profile with a center punch, where the roller “falls through”. This method is more reliable, but requires high accuracy.

What to do so that the doors do not creak when opened

The sash rollers rotate on bearings, so they move very easily. Sometimes hair gets into the grooves of the guides, which are wound around the roller axis and block it. As a result, the wheels do not spin, but simply rub along the profile, making a characteristic sound.

Illustration: Artyom Kozoriz / Lifehacker

The solution is this: lift the door and place a wedge or something similar under it to fix it. Use tweezers or other improvised means to free the roller from the hair. After that, the wheels will rotate normally again. For prevention, you can additionally lubricate the axle with a couple of drops of engine oil.

If you do not get rid of the problem in time, then the rollers will simply be erased, lose their roundness and will no longer be able to spin. You will have to change them for new ones.

How to repair a closet if the doors are hard to open

The flaps move reluctantly when something interferes with them. Most often it is dust and dirt that clogs into the grooves. So check the guides first. If necessary, remove all debris with a thin object, and then vacuum.

Never lubricate the guides with oil to reduce friction. This will not solve the problem, but will exacerbate it: dust will only stick to the oil more strongly.

If the profile is clean, then the door itself probably sank. In this situation, it rubs against the guide and wedges. To fix this, raise the doors a few millimeters by turning the roller screws on each side clockwise.

Illustration: Artyom Kozoriz / Lifehacker

Such a breakdown can also be a running case of a previous problem. Raise the sash and inspect the roller: if it is worn out, replace it with a new one.

What to do if the doors cling to each other

Each of the wings is in its own groove of the guides, and when moving, they do not touch each other. If the doors cling, there can be two reasons.

Illustration: Artyom Kozoriz / Lifehacker

From vibration or unreliable fastening, the side profiles of the wings sometimes become loose and begin to touch each other. To fix this, turn the fixing screws clockwise. It is easy to find them: there is only one on top, and at the bottom you need to touch the screw, which is located next to the adjusting one, that is, the second from the bottom.

The second possible reason: during adjustment or under its own weight, the door sank and warped to one side. Because of this, one edge is higher and rests against the upper guide or rubs against the other sash. To get rid of the problem, adjust the sash in height: unscrew the adjusting (lower) screw counterclockwise.

Read also 🔨⚙️

Leave a Reply

Your email address will not be published.